Edit: November 10th, 2023 18:04 GMT: Fixed positioning calculations for RAM in Micro and Mini modes when sys-clk is not working.If sys-clk 2.0.0_rc4+ is active, Micro mode shows next to frequencies instead of also △ if real frequency is higher by 20 MHz than expected, ▽ if it's lower by 20 MHz, ≠ if it's lower by 50 MHz (seeing ≠ for longer than few seconds without any change suggests that your overclocking solution is bugged).Show proper button icons in Full mode (only exceptions are general UP, DOWN, LEFT and RIGHT because they include both Sticks and D-Pad).Remove option to change position of Mini and FPS Counter modes with button combo.Remove option to change refresh rate with button combo.Allow reading RAM load from sys-clk 2.0.0_rc4+.Allow reading real frequencies from sys-clk 2.0.0_rc4+ sysmodule, if not installed showed frequencies in Mini and Micro modes are falling back to target frequencies.If someone wants to bring back old combo, use status-monitor config file. Now default combo button is L + D-PAD Down + R Stick.Button combos are read from 3 different configurations files, the most important is status-monitor config, next config used by Ultrahand overlay, and last config for Tesla Menu.Introduction of experimental configuration file, which allows changing exit button combo, Mini + Micro + FPS Counter + FPS Graph UIs, refresh rates.Sometimes exiting mode resulted in exiting overlay.Temperatures for PCB and SoC were swapped in 0.9.2 release.This release also includes 2 shadow updates for 1.0.0, which includes fixes for overflowing of real frequencies + deltas, and also fixed RAM positioning calculations in Micro and Mini modes.Allow hiding real frequencies, deltas and target frequencies in Full mode (deltas are not showed if both real + target frequencies are hidden).Move FPS Graph and FPS Counter to one subcategory "FPS".Changed i2c communication code to avoid issues with wrong readings (thanks to ~lineon).Removed whole logic behind PR #56 instead relying now on max17050 TTE register.Changing battery_avg_iir_filter to true results in period time of average voltage being changed to 45s, and 11.25s for amperage.Add new keys to config: battery_avg_iir_filter and battery_time_left_refreshrate, more in CONFIG.Resident Evil 5 (Nintendo Switch) - Status Monitor Overlay and NX-FPS ( Marek) Delete sigpatches, change your Switch to primary device, unlink account, or disable Wi-Fi. Your Switch is using sigpatches, is not a primary device, is using linked account, and is connected to network.Find out in atmosphere/contents any sysmodule that you don't need, delete it and restart Switch. You're using some untested custom sysmodule that has no proper thread sleeping implemented.If you must use it, only solution is to use this overlay only in airplane mode. Find any folder in atmosphere/exefs_patches/ that has in folder name nifm, nfim and/or ctest, delete this folder and restart Switch. But they cause nifm to randomly rampage when connected to network. Those patches allow to connect to network that has no internet connection. You're using nifm services connection test patches (in short nifm ctest patches) that are included in various packs.When opening Full or Mini mode, overlay is showing that Core #3 usage is at 100% while everything else is showing 0, eventually leading to crash. Almost everything is done on Core #3, other cores usage is below 0.001%. Negligible, you won't see any difference. If it's not working in dock, you need to first start Status Monitor, then put Nintendo Switch to dock. You can exit from selected mode by pressing and holding Left Stick + Right Stick. Tool contains six modes to choose, each one is explained here. Restart Switch, you can then access overlays by pressing all 3 buttons at once: L, D-Pad Down and Right Stick (aka pressing it). Place Status-Monitor-Overlay.ovl to /switch/.overlays/ folder.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |